Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library
Dimensions, basic dynamic load ratings (Cr), static ratings (C0r), and RPM limits for ISO metric radial ball bearings.
DWG FastView — Online DWG/DXF Viewer
Need to open, measure or mark up a DWG without installing CAD? DWG FastView runs in the browser. This is a sponsored placement and has no effect on the results of the tool above.
Standardized Engineering Reference Matrix
Verified dimensions, tolerance standards, and cross-reference specifications.
| Bearing Designation | Bore d (mm) | Outer Dia D (mm) | Width B (mm) | Basic Dynamic Rating Cr (kN) | Basic Static Rating C0r (kN) | Limiting Speed (RPM grease) | Action |
|---|---|---|---|---|---|---|---|
| 6000 | 10 | 26 | 8 | 4.55 | 1.97 | 30,000 | |
| 6004 | 20 | 42 | 12 | 9.38 | 5.02 | 17,000 | |
| 6008 | 40 | 68 | 15 | 16.8 | 11.5 | 9,500 | |
| 6200 | 10 | 30 | 9 | 5.10 | 2.39 | 24,000 | |
| 6204 | 20 | 47 | 14 | 12.8 | 6.65 | 15,000 | |
| 6205 | 25 | 52 | 15 | 14.0 | 7.85 | 13,000 | |
| 6208 | 40 | 80 | 18 | 29.1 | 17.8 | 8,500 | |
| 6304 | 20 | 52 | 15 | 15.9 | 7.80 | 13,000 | |
| 6308 | 40 | 90 | 23 | 40.5 | 24.0 | 7,500 |
Next Steps in Your Mechanical Workflow
Handpicked calculators, parsers, and shortcuts for sheet metal, modeling & fabrication
ANSI / ASME B1.1 Unified Inch Screw Threads (UNC / UNF) Database
Standard dimensions for Unified inch fasteners: major diameter, TPI, pitch diameter, minor diameter, and recommended tap drill sizes.
ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6)
Standard metric limits and fits database per ISO 286: hole and shaft upper/lower deviations (μm) for clearance, transition, and press fits.
AISC Standard Steel Shapes Structural Properties Library
Comprehensive dimensional and structural property database for AISC wide-flange beams (W-Shapes), I-beams, channels, and angles.
Standard Fasteners Specification Library
Searchable library of ISO, DIN, ANSI, and JIS fastener specifications: bolts, screws, nuts, washers, pins, and rivets.
HVAC & Mechanical Drawing Symbols Reference Library
Interactive reference for HVAC, ductwork, piping, and mechanical equipment symbols per ASHRAE and ISO standards.
K-Factor & Bend Allowance Calc
Calculate sheet metal neutral axis shift, bend deductions, and flat pattern blank sizes per DIN 6935.
Engineering Methodology & Design Standards: Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library
Discipline: Mechanical Power Transmission & Tribology
Governing Mathematical Formulation
In professional Mechanical Power Transmission & Tribology workflows, accurate sizing and performance verification require consistent unit normalization and adherence to closed-form analytical mechanics. This Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library utility implements the standardized engineering formulation:
Dimensions, basic dynamic load ratings (Cr), static ratings (C0r), and RPM limits for ISO metric radial ball bearings.Dimensions, basic dynamic load ratings (Cr), static ratings (C0r), and RPM limits for ISO metric radial ball bearings. Every input change triggers an instant client-side recalculation across all coupled dependent variables, enabling rapid sensitivity analysis during preliminary and detailed CAD design phases.
Applicable Codes, Standards & CAD Integration
Verify shaft and housing cylindrical tolerance fits (typically ISO k5/m5 shaft with H7 housing bore per ISO 286) in your 3D MCAD assembly before finalizing bearing selection.
Engineering Verification Note: Analytical models assume homogeneous material behavior, steady-state boundary loading, and consistent dimensional units. Always apply appropriate service factors, corrosion allowances, or load and resistance factor design (LRFD / ASD) safety margins required by your governing code.
Parameter Specifications & Worked Engineering Example
Baseline reference case using default design values for Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library
Step-by-Step Benchmark Walkthrough
- Define Design Boundary Conditions: Establish the nominal operating parameters for the component or system:
Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = ISO 281:2007 (Dynamic Load Ratings & Rating Life). Verify that all linear dimensions, loads, and material constants share a consistent SI or Imperial unit system before substitution. - Execute Analytical Formulation: Substitute the normalized input vector into the governing relation (
Dimensions, basic dynamic load ratings (Cr), static ratings (C0r), and RPM limits for ISO metric radial ball bearings.) in accordance with ISO 281:2007 (Dynamic Load Ratings & Rating Life), ISO 76 (Static Load Ratings), ANSI/ABMA Std 9 & Std 11. - Verify Computed Engineering Outputs: For the baseline design case, the calculator yields
Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready. Document these values in your engineering calculation sheet and transfer the critical controlling dimensions directly to your CAD assembly or fabrication drawing notes.
Frequently Asked Engineering Questions
Technical reference & verification guidelines for Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library
What governing equation and methodology does the Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library use?
The Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library evaluates dimensions, basic dynamic load ratings (cr), static ratings (c0r), and rpm limits for iso metric radial ball bearings within the Mechanical Power Transmission & Tribology domain using the governing formulation: Dimensions, basic dynamic load ratings (Cr), static ratings (C0r), and RPM limits for ISO metric radial ball bearings.. All intermediate quantities are computed in double-precision floating-point arithmetic to prevent cumulative rounding drift before final design verification.
Which international engineering standards apply to Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library calculations?
Calculations and boundary assumptions in this utility align with recognized industry references including ISO 281:2007 (Dynamic Load Ratings & Rating Life), ISO 76 (Static Load Ratings), ANSI/ABMA Std 9 & Std 11. When preparing formal calculation packages or P.E. stamp submittals, always verify local jurisdictional code amendments and project-specific safety factors.
How should I integrate results from the Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library into my CAD or BIM workflow?
Verify shaft and housing cylindrical tolerance fits (typically ISO k5/m5 shaft with H7 housing bore per ISO 286) in your 3D MCAD assembly before finalizing bearing selection. Using the baseline benchmark (Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = ISO 281:2007 (Dynamic Load Ratings & Rating Life)), the solver yields Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready, which can be directly cross-referenced against your parametric 3D assembly constraints, 2D fabrication drawings, or bill of materials (BOM).