ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6)
Standard metric limits and fits database per ISO 286: hole and shaft upper/lower deviations (μm) for clearance, transition, and press fits.
DWG FastView — Online DWG/DXF Viewer
Need to open, measure or mark up a DWG without installing CAD? DWG FastView runs in the browser. This is a sponsored placement and has no effect on the results of the tool above.
Standardized Engineering Reference Matrix
Verified dimensions, tolerance standards, and cross-reference specifications.
| Nominal Diameter Range (mm) | Hole H7 (μm) | Hole H8 (μm) | Shaft g6 (μm) | Shaft h6 (μm) | Shaft p6 (Press Fit, μm) | Typical Fit Character | Action |
|---|---|---|---|---|---|---|---|
| Over 3 to 6 | +12 / 0 | +18 / 0 | -4 / -12 | 0 / -8 | +20 / +12 | H7/g6: Sliding fit; H7/p6: Permanent press fit | |
| Over 6 to 10 | +15 / 0 | +22 / 0 | -5 / -14 | 0 / -9 | +24 / +15 | H7/g6: Free running; H7/h6: Locating clearance | |
| Over 10 to 18 | +18 / 0 | +27 / 0 | -6 / -17 | 0 / -11 | +29 / +18 | H7/h6: Push fit; H7/p6: Light drive fit | |
| Over 18 to 30 | +21 / 0 | +33 / 0 | -7 / -20 | 0 / -13 | +35 / +22 | H7/g6: Precision bearing seat; H7/p6: Heavy press | |
| Over 30 to 50 | +25 / 0 | +39 / 0 | -9 / -25 | 0 / -16 | +42 / +26 | H7/h6: Keyed hub; H7/p6: Bushing interference | |
| Over 50 to 80 | +30 / 0 | +46 / 0 | -10 / -29 | 0 / -19 | +51 / +32 | H7/g6: Machine spindle; H7/p6: Gear hub press | |
| Over 80 to 120 | +35 / 0 | +54 / 0 | -12 / -34 | 0 / -22 | +59 / +37 | H7/h6: Flange spigot; H7/p6: Crank pin press |
Recommended Engineering & CAD Utilities
Handpicked companion tools to streamline modeling, calculation, and drafting workflows
ISO 286 Mechanical Limits and Fits Calculator
Enter shaft and hole dimensions to instantly calculate engineering tolerances and fit classifications.
ISO 286 Limits & Fits Tolerance Grade Reference Table
Interactive lookup for ISO 286 standard tolerance grades (IT01-IT18) and fundamental deviations for shaft and hole fits.
DIN 6885 / ISO 773 Parallel Drive Keys & Keyway Tolerances Reference Table
Standard metric parallel keyway dimensions for drive shafts: key section b x h, shaft depth t1, hub depth t2, and fit tolerances.
ISO 286 Limits & Fits Reference Table
Searchable ISO 286-1/2 limits and fits reference: IT tolerance grades, shaft/hole fundamental deviations, and common fit combinations with applications.
Deep Groove Ball Bearings (6000, 6200, 6300 Series) Specification Library
Dimensions, basic dynamic load ratings (Cr), static ratings (C0r), and RPM limits for ISO metric radial ball bearings.
SolidWorks vs Fusion 360
Deep side-by-side comparison of parametric modeling, cloud PDM, CAM, and pricing in 2026.
Engineering Methodology & Design Standards: ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6)
Discipline: CNC Machining, Sheet Metal Fabrication & Dimensional Metrology
Governing Mathematical Formulation
In professional CNC Machining, Sheet Metal Fabrication & Dimensional Metrology workflows, accurate sizing and performance verification require consistent unit normalization and adherence to closed-form analytical mechanics. This ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6) utility implements the standardized engineering formulation:
Standard metric limits and fits database per ISO 286: hole and shaft upper/lower deviations (μm) for clearance, transition, and press fits.Standard metric limits and fits database per ISO 286: hole and shaft upper/lower deviations (μm) for clearance, transition, and press fits. Every input change triggers an instant client-side recalculation across all coupled dependent variables, enabling rapid sensitivity analysis during preliminary and detailed CAD design phases.
Applicable Codes, Standards & CAD Integration
Synchronize sheet metal K-factors, tool radius compensation registers (G41/G42), and GD&T datum reference frames between your 3D CAD master model, CAM post-processor, and CMM inspection plan.
Engineering Verification Note: Analytical models assume homogeneous material behavior, steady-state boundary loading, and consistent dimensional units. Always apply appropriate service factors, corrosion allowances, or load and resistance factor design (LRFD / ASD) safety margins required by your governing code.
Parameter Specifications & Worked Engineering Example
Baseline reference case using default design values for ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6)
Step-by-Step Benchmark Walkthrough
- Define Design Boundary Conditions: Establish the nominal operating parameters for the component or system:
Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = ISO 286-1 / ASME B4.1 (Limits and Fits). Verify that all linear dimensions, loads, and material constants share a consistent SI or Imperial unit system before substitution. - Execute Analytical Formulation: Substitute the normalized input vector into the governing relation (
Standard metric limits and fits database per ISO 286: hole and shaft upper/lower deviations (μm) for clearance, transition, and press fits.) in accordance with ISO 286-1 / ASME B4.1 (Limits and Fits), ASME Y14.5-2018 / ISO 1101 (GD&T), DIN 6935 (Sheet Metal Cold Bending), ISO 2768 (General Tolerances). - Verify Computed Engineering Outputs: For the baseline design case, the calculator yields
Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready. Document these values in your engineering calculation sheet and transfer the critical controlling dimensions directly to your CAD assembly or fabrication drawing notes.
Frequently Asked Engineering Questions
Technical reference & verification guidelines for ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6)
What governing equation and methodology does the ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6) use?
The ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6) evaluates standard metric limits and fits database per iso 286: hole and shaft upper/lower deviations (μm) for clearance, transition, and press fits within the CNC Machining, Sheet Metal Fabrication & Dimensional Metrology domain using the governing formulation: Standard metric limits and fits database per ISO 286: hole and shaft upper/lower deviations (μm) for clearance, transition, and press fits.. All intermediate quantities are computed in double-precision floating-point arithmetic to prevent cumulative rounding drift before final design verification.
Which international engineering standards apply to ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6) calculations?
Calculations and boundary assumptions in this utility align with recognized industry references including ISO 286-1 / ASME B4.1 (Limits and Fits), ASME Y14.5-2018 / ISO 1101 (GD&T), DIN 6935 (Sheet Metal Cold Bending), ISO 2768 (General Tolerances). When preparing formal calculation packages or P.E. stamp submittals, always verify local jurisdictional code amendments and project-specific safety factors.
How should I integrate results from the ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6) into my CAD or BIM workflow?
Synchronize sheet metal K-factors, tool radius compensation registers (G41/G42), and GD&T datum reference frames between your 3D CAD master model, CAM post-processor, and CMM inspection plan. Using the baseline benchmark (Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = ISO 286-1 / ASME B4.1 (Limits and Fits)), the solver yields Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready, which can be directly cross-referenced against your parametric 3D assembly constraints, 2D fabrication drawings, or bill of materials (BOM).