AISC Standard Steel Shapes Structural Properties Library
Comprehensive dimensional and structural property database for AISC wide-flange beams (W-Shapes), I-beams, channels, and angles.
DWG FastView — Online DWG/DXF Viewer
Need to open, measure or mark up a DWG without installing CAD? DWG FastView runs in the browser. This is a sponsored placement and has no effect on the results of the tool above.
Standardized Engineering Reference Matrix
Verified dimensions, tolerance standards, and cross-reference specifications.
| AISC Designation | Nominal Depth d (in / mm) | Flange Width bf (in / mm) | Flange Thick tf (in / mm) | Area A (in² / mm²) | Elastic Modulus Wx (in³ / cm³) | Moment of Inertia Ix (in⁴ / cm⁴) | Action |
|---|---|---|---|---|---|---|---|
| W8x24 | 7.93 in (201 mm) | 6.50 in (165 mm) | 0.400 in (10.2 mm) | 7.08 in² (4560 mm²) | 20.9 in³ (342 cm³) | 82.7 in⁴ (3440 cm⁴) | |
| W10x33 | 9.73 in (247 mm) | 7.96 in (202 mm) | 0.435 in (11.0 mm) | 9.71 in² (6260 mm²) | 35.0 in³ (574 cm³) | 170 in⁴ (7080 cm⁴) | |
| W12x45 | 12.06 in (306 mm) | 8.05 in (204 mm) | 0.575 in (14.6 mm) | 13.2 in² (8520 mm²) | 58.1 in³ (952 cm³) | 350 in⁴ (14600 cm⁴) | |
| W14x68 | 14.04 in (357 mm) | 10.04 in (255 mm) | 0.720 in (18.3 mm) | 20.0 in² (12900 mm²) | 103 in³ (1690 cm³) | 722 in⁴ (30100 cm⁴) | |
| W16x89 | 16.75 in (425 mm) | 10.27 in (261 mm) | 0.875 in (22.2 mm) | 26.2 in² (16900 mm²) | 153 in³ (2510 cm³) | 1300 in⁴ (54100 cm⁴) | |
| W18x97 | 18.59 in (472 mm) | 11.15 in (283 mm) | 0.870 in (22.1 mm) | 28.5 in² (18400 mm²) | 188 in³ (3080 cm³) | 1750 in⁴ (72800 cm⁴) | |
| W21x101 | 21.36 in (543 mm) | 12.29 in (312 mm) | 0.800 in (20.3 mm) | 29.8 in² (19200 mm²) | 227 in³ (3720 cm³) | 2420 in⁴ (101000 cm⁴) | |
| W24x104 | 24.06 in (611 mm) | 12.75 in (324 mm) | 0.750 in (19.1 mm) | 30.6 in² (19700 mm²) | 258 in³ (4230 cm³) | 3100 in⁴ (129000 cm⁴) |
Recommended Engineering & CAD Utilities
Handpicked companion tools to streamline modeling, calculation, and drafting workflows
Steel Bolt Group Load Analysis Calculator
Analyze bolt group connections for maximum bolt force under eccentric loading per AISC methodology.
Eurocode DIN / EN Structural Steel Profiles Library (IPE, HEA, HEB)
Dimensional and geometric properties of European structural steel profiles: IPE beams, HEA/HEB wide-flange columns per EN 10034 / EN 10025.
Thread Engagement Length & Pull-Out Safety Checker
Calculate minimum safe thread engagement depth and shear area for bolted joints across steel, cast iron, and aluminum substrates.
ANSI / ASME B1.1 Unified Inch Screw Threads (UNC / UNF) Database
Standard dimensions for Unified inch fasteners: major diameter, TPI, pitch diameter, minor diameter, and recommended tap drill sizes.
Engineering Material Properties Reference Table
Mechanical properties of steel, aluminum, copper, titanium, brass, and engineering plastics: density, yield strength, elastic modulus, Poisson ratio, and thermal expansion.
Revit Family Parameter Calculator
Audit nested family formulas, flex geometry constraints, and streamline model performance.
Engineering Methodology & Design Standards: AISC Standard Steel Shapes Structural Properties Library
Discipline: Engineering Metrology, SI/Imperial Unit Conversion & Applied Physics
Governing Mathematical Formulation
In professional Engineering Metrology, SI/Imperial Unit Conversion & Applied Physics workflows, accurate sizing and performance verification require consistent unit normalization and adherence to closed-form analytical mechanics. This AISC Standard Steel Shapes Structural Properties Library utility implements the standardized engineering formulation:
Comprehensive dimensional and structural property database for AISC wide-flange beams (W-Shapes), I-beams, channels, and angles.Comprehensive dimensional and structural property database for AISC wide-flange beams (W-Shapes), I-beams, channels, and angles. Every input change triggers an instant client-side recalculation across all coupled dependent variables, enabling rapid sensitivity analysis during preliminary and detailed CAD design phases.
Applicable Codes, Standards & CAD Integration
Maintain full double-precision floating-point accuracy during intermediate engineering calculations and apply rounding only to final drawing callouts per ASME Y14.5 / ISO 80000 rules.
Engineering Verification Note: Analytical models assume homogeneous material behavior, steady-state boundary loading, and consistent dimensional units. Always apply appropriate service factors, corrosion allowances, or load and resistance factor design (LRFD / ASD) safety margins required by your governing code.
Parameter Specifications & Worked Engineering Example
Baseline reference case using default design values for AISC Standard Steel Shapes Structural Properties Library
Step-by-Step Benchmark Walkthrough
- Define Design Boundary Conditions: Establish the nominal operating parameters for the component or system:
Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = NIST Special Publication 811 (Guide for the Use of the International System of Units). Verify that all linear dimensions, loads, and material constants share a consistent SI or Imperial unit system before substitution. - Execute Analytical Formulation: Substitute the normalized input vector into the governing relation (
Comprehensive dimensional and structural property database for AISC wide-flange beams (W-Shapes), I-beams, channels, and angles.) in accordance with NIST Special Publication 811 (Guide for the Use of the International System of Units), ISO 80000-1 (Quantities and Units), BIPM SI Brochure (9th Edition). - Verify Computed Engineering Outputs: For the baseline design case, the calculator yields
Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready. Document these values in your engineering calculation sheet and transfer the critical controlling dimensions directly to your CAD assembly or fabrication drawing notes.
Frequently Asked Engineering Questions
Technical reference & verification guidelines for AISC Standard Steel Shapes Structural Properties Library
What governing equation and methodology does the AISC Standard Steel Shapes Structural Properties Library use?
The AISC Standard Steel Shapes Structural Properties Library evaluates comprehensive dimensional and structural property database for aisc wide-flange beams (w-shapes), i-beams, channels, and angles within the Engineering Metrology, SI/Imperial Unit Conversion & Applied Physics domain using the governing formulation: Comprehensive dimensional and structural property database for AISC wide-flange beams (W-Shapes), I-beams, channels, and angles.. All intermediate quantities are computed in double-precision floating-point arithmetic to prevent cumulative rounding drift before final design verification.
Which international engineering standards apply to AISC Standard Steel Shapes Structural Properties Library calculations?
Calculations and boundary assumptions in this utility align with recognized industry references including NIST Special Publication 811 (Guide for the Use of the International System of Units), ISO 80000-1 (Quantities and Units), BIPM SI Brochure (9th Edition). When preparing formal calculation packages or P.E. stamp submittals, always verify local jurisdictional code amendments and project-specific safety factors.
How should I integrate results from the AISC Standard Steel Shapes Structural Properties Library into my CAD or BIM workflow?
Maintain full double-precision floating-point accuracy during intermediate engineering calculations and apply rounding only to final drawing callouts per ASME Y14.5 / ISO 80000 rules. Using the baseline benchmark (Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = NIST Special Publication 811 (Guide for the Use of the International System of Units)), the solver yields Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready, which can be directly cross-referenced against your parametric 3D assembly constraints, 2D fabrication drawings, or bill of materials (BOM).