Engineering Thermoplastics Properties & Machinability Database
Physical, mechanical, and thermal properties of engineering plastics: POM (Delrin), PA66 (Nylon), PEEK, PTFE (Teflon), and Polycarbonate.
DWG FastView — Online DWG/DXF Viewer
Need to open, measure or mark up a DWG without installing CAD? DWG FastView runs in the browser. This is a sponsored placement and has no effect on the results of the tool above.
Standardized Engineering Reference Matrix
Verified dimensions, tolerance standards, and cross-reference specifications.
| Polymer (Abbreviation) | Tensile Strength (MPa) | Flexural Modulus (GPa) | Heat Deflection Temp HDT (°C @ 0.45MPa) | Density (g/cm³) | Machining & Friction Characteristics | Action |
|---|---|---|---|---|---|---|
| Delrin / POM-Acetal | 65 - 72 | 2.8 - 3.2 | 160°C | 1.41 | Outstanding dimensional stability; low moisture absorption; CNC milling favorite. | |
| Nylon 6/6 (PA66) | 75 - 85 | 2.8 - 3.4 | 180°C | 1.14 | High wear resistance; self-lubricating; hygroscopic (swells in humid conditions). | |
| PEEK (Polyether ether ketone) | 95 - 105 | 3.8 - 4.2 | 250°C | 1.32 | Aerospace & medical grade; extreme chemical resistance; continuous 250°C service. | |
| PTFE (Teflon) | 20 - 35 | 0.5 - 0.7 | 120°C | 2.18 | Near-zero friction coefficient; chemically inert; creeps under high static mechanical load. | |
| UHMW-PE | 22 - 35 | 0.7 - 0.9 | 80°C | 0.94 | Extreme abrasion resistance; low friction chutes & guide rails; difficult to glue. | |
| Polycarbonate (PC) | 60 - 75 | 2.2 - 2.5 | 135°C | 1.20 | Optical clarity; extremely high impact strength; prone to chemical stress cracking. |
Recommended Engineering & CAD Utilities
Handpicked companion tools to streamline modeling, calculation, and drafting workflows
ISO 286 Limits and Fits Engineering Tolerances Database (H7/g6, H7/p6)
Standard metric limits and fits database per ISO 286: hole and shaft upper/lower deviations (μm) for clearance, transition, and press fits.
Engineering Material Properties Database
Searchable database of 200+ engineering materials with mechanical, thermal, and electrical properties.
Engineering Material Properties Reference Table
Mechanical properties of steel, aluminum, copper, titanium, brass, and engineering plastics: density, yield strength, elastic modulus, Poisson ratio, and thermal expansion.
AISC Standard Steel Shapes Structural Properties Library
Comprehensive dimensional and structural property database for AISC wide-flange beams (W-Shapes), I-beams, channels, and angles.
CAD Symbol & Block Library
Browseable library of 500+ common engineering symbols as downloadable SVG and DXF: electrical, hydraulic, pneumatic, and architectural.
Blender Keyboard Shortcuts Reference
Comprehensive hotkeys for 3D modeling, mesh editing, sculpting brushes, and Cycles rendering.
Engineering Methodology & Design Standards: Engineering Thermoplastics Properties & Machinability Database
Discipline: HVAC, Psychrometrics & Building Thermal Systems
Governing Mathematical Formulation
In professional HVAC, Psychrometrics & Building Thermal Systems workflows, accurate sizing and performance verification require consistent unit normalization and adherence to closed-form analytical mechanics. This Engineering Thermoplastics Properties & Machinability Database utility implements the standardized engineering formulation:
Physical, mechanical, and thermal properties of engineering plastics: POM (Delrin), PA66 (Nylon), PEEK, PTFE (Teflon), and Polycarbonate.Physical, mechanical, and thermal properties of engineering plastics: POM (Delrin), PA66 (Nylon), PEEK, PTFE (Teflon), and Polycarbonate. Every input change triggers an instant client-side recalculation across all coupled dependent variables, enabling rapid sensitivity analysis during preliminary and detailed CAD design phases.
Applicable Codes, Standards & CAD Integration
Coordinate ductwork aspect ratios, acoustic lining thickness, and ceiling plenum clearances within your federated MEP BIM model to avoid field routing clashes and excessive static pressure drops.
Engineering Verification Note: Analytical models assume homogeneous material behavior, steady-state boundary loading, and consistent dimensional units. Always apply appropriate service factors, corrosion allowances, or load and resistance factor design (LRFD / ASD) safety margins required by your governing code.
Parameter Specifications & Worked Engineering Example
Baseline reference case using default design values for Engineering Thermoplastics Properties & Machinability Database
Step-by-Step Benchmark Walkthrough
- Define Design Boundary Conditions: Establish the nominal operating parameters for the component or system:
Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = ASHRAE Handbook — Fundamentals & HVAC Systems and Equipment. Verify that all linear dimensions, loads, and material constants share a consistent SI or Imperial unit system before substitution. - Execute Analytical Formulation: Substitute the normalized input vector into the governing relation (
Physical, mechanical, and thermal properties of engineering plastics: POM (Delrin), PA66 (Nylon), PEEK, PTFE (Teflon), and Polycarbonate.) in accordance with ASHRAE Handbook — Fundamentals & HVAC Systems and Equipment, SMACNA HVAC Duct Construction Standards, ISO 6946, ASHRAE Standard 62.1 & 90.1. - Verify Computed Engineering Outputs: For the baseline design case, the calculator yields
Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready. Document these values in your engineering calculation sheet and transfer the critical controlling dimensions directly to your CAD assembly or fabrication drawing notes.
Frequently Asked Engineering Questions
Technical reference & verification guidelines for Engineering Thermoplastics Properties & Machinability Database
What governing equation and methodology does the Engineering Thermoplastics Properties & Machinability Database use?
The Engineering Thermoplastics Properties & Machinability Database evaluates physical, mechanical, and thermal properties of engineering plastics: pom (delrin), pa66 (nylon), peek, ptfe (teflon), and polycarbonate within the HVAC, Psychrometrics & Building Thermal Systems domain using the governing formulation: Physical, mechanical, and thermal properties of engineering plastics: POM (Delrin), PA66 (Nylon), PEEK, PTFE (Teflon), and Polycarbonate.. All intermediate quantities are computed in double-precision floating-point arithmetic to prevent cumulative rounding drift before final design verification.
Which international engineering standards apply to Engineering Thermoplastics Properties & Machinability Database calculations?
Calculations and boundary assumptions in this utility align with recognized industry references including ASHRAE Handbook — Fundamentals & HVAC Systems and Equipment, SMACNA HVAC Duct Construction Standards, ISO 6946, ASHRAE Standard 62.1 & 90.1. When preparing formal calculation packages or P.E. stamp submittals, always verify local jurisdictional code amendments and project-specific safety factors.
How should I integrate results from the Engineering Thermoplastics Properties & Machinability Database into my CAD or BIM workflow?
Coordinate ductwork aspect ratios, acoustic lining thickness, and ceiling plenum clearances within your federated MEP BIM model to avoid field routing clashes and excessive static pressure drops. Using the baseline benchmark (Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = ASHRAE Handbook — Fundamentals & HVAC Systems and Equipment), the solver yields Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready, which can be directly cross-referenced against your parametric 3D assembly constraints, 2D fabrication drawings, or bill of materials (BOM).