Engineering Material Properties Database
Searchable database of 200+ engineering materials with mechanical, thermal, and electrical properties.
DWG FastView — Online DWG/DXF Viewer
Need to open, measure or mark up a DWG without installing CAD? DWG FastView runs in the browser. This is a sponsored placement and has no effect on the results of the tool above.
Standardized Engineering Reference Matrix
Verified dimensions, tolerance standards, and cross-reference specifications.
| Material Grade | Category | Density ρ (g/cm³) | Young's Modulus E (GPa) | Yield Strength σy (MPa) | Ultimate Tensile σu (MPa) | Thermal Cond. k (W/m·K) | Poisson's Ratio ν | Action |
|---|---|---|---|---|---|---|---|---|
| Structural Steel S235 / A36 | Carbon Steel | 7.85 | 200 GPa | 235 – 250 MPa | 400 – 550 MPa | 50 W/m·K | 0.30 | |
| Alloy Steel 4140 (Q&T) | Chromoly Steel | 7.85 | 205 GPa | 655 MPa | 1020 MPa | 42.6 W/m·K | 0.29 | |
| Stainless Steel 304 (1.4301) | Austenitic SS | 8.00 | 193 GPa | 215 MPa | 505 MPa | 16.2 W/m·K | 0.29 | |
| Stainless Steel 316L (1.4404) | Marine Austenitic SS | 8.00 | 193 GPa | 170 MPa | 485 MPa | 16.3 W/m·K | 0.30 | |
| Aluminum 6061-T6 | Wrought Aluminum | 2.70 | 68.9 GPa | 276 MPa | 310 MPa | 167 W/m·K | 0.33 | |
| Aluminum 7075-T6 | Aerospace Aluminum | 2.81 | 71.7 GPa | 503 MPa | 572 MPa | 130 W/m·K | 0.33 | |
| Titanium Ti-6Al-4V (Grade 5) | Titanium Alloy | 4.43 | 113.8 GPa | 880 MPa | 950 MPa | 6.7 W/m·K | 0.34 | |
| Brass C36000 (Free-Cutting) | Copper Alloy | 8.50 | 97 GPa | 310 MPa | 385 MPa | 115 W/m·K | 0.34 | |
| Copper C11000 (ETP) | Pure Copper | 8.89 | 117 GPa | 220 MPa (Half-Hard) | 270 MPa | 388 W/m·K | 0.34 | |
| Grey Cast Iron EN-GJL-250 | Ferrous Casting | 7.20 | 110 GPa | 165 MPa (0.1% Offset) | 250 MPa (Tensile) | 46 W/m·K | 0.26 |
Recommended Engineering & CAD Utilities
Handpicked companion tools to streamline modeling, calculation, and drafting workflows
Engineering Material Properties Reference Table
Mechanical properties of steel, aluminum, copper, titanium, brass, and engineering plastics: density, yield strength, elastic modulus, Poisson ratio, and thermal expansion.
AISC Standard Steel Shapes Structural Properties Library
Comprehensive dimensional and structural property database for AISC wide-flange beams (W-Shapes), I-beams, channels, and angles.
Engineering Thermoplastics Properties & Machinability Database
Physical, mechanical, and thermal properties of engineering plastics: POM (Delrin), PA66 (Nylon), PEEK, PTFE (Teflon), and Polycarbonate.
Laser Cutting Speed Calculator
Calculate laser cutting speed from power, material thickness, and absorption.
SolidWorks SLDPRT to 3MF Converter
Convert SolidWorks SLDPRT parts and multi-body weldments to 3MF for multi-material 3D printing on Bambu Lab, Prusa, and Voron printers.
5-Year CAD Subscription vs. Perpetual TCO
Compare 5-year cumulative SaaS rental costs vs. one-time perpetual buyout CAD alternatives.
Engineering Methodology & Design Standards: Engineering Material Properties Database
Discipline: Engineering Metrology, SI/Imperial Unit Conversion & Applied Physics
Governing Mathematical Formulation
In professional Engineering Metrology, SI/Imperial Unit Conversion & Applied Physics workflows, accurate sizing and performance verification require consistent unit normalization and adherence to closed-form analytical mechanics. This Engineering Material Properties Database utility implements the standardized engineering formulation:
Searchable database of 200+ engineering materials with mechanical, thermal, and electrical properties.Searchable database of 200+ engineering materials with mechanical, thermal, and electrical properties. Every input change triggers an instant client-side recalculation across all coupled dependent variables, enabling rapid sensitivity analysis during preliminary and detailed CAD design phases.
Applicable Codes, Standards & CAD Integration
Maintain full double-precision floating-point accuracy during intermediate engineering calculations and apply rounding only to final drawing callouts per ASME Y14.5 / ISO 80000 rules.
Engineering Verification Note: Analytical models assume homogeneous material behavior, steady-state boundary loading, and consistent dimensional units. Always apply appropriate service factors, corrosion allowances, or load and resistance factor design (LRFD / ASD) safety margins required by your governing code.
Parameter Specifications & Worked Engineering Example
Baseline reference case using default design values for Engineering Material Properties Database
Step-by-Step Benchmark Walkthrough
- Define Design Boundary Conditions: Establish the nominal operating parameters for the component or system:
Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = NIST Special Publication 811 (Guide for the Use of the International System of Units). Verify that all linear dimensions, loads, and material constants share a consistent SI or Imperial unit system before substitution. - Execute Analytical Formulation: Substitute the normalized input vector into the governing relation (
Searchable database of 200+ engineering materials with mechanical, thermal, and electrical properties.) in accordance with NIST Special Publication 811 (Guide for the Use of the International System of Units), ISO 80000-1 (Quantities and Units), BIPM SI Brochure (9th Edition). - Verify Computed Engineering Outputs: For the baseline design case, the calculator yields
Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready. Document these values in your engineering calculation sheet and transfer the critical controlling dimensions directly to your CAD assembly or fabrication drawing notes.
Frequently Asked Engineering Questions
Technical reference & verification guidelines for Engineering Material Properties Database
What governing equation and methodology does the Engineering Material Properties Database use?
The Engineering Material Properties Database evaluates searchable database of 200+ engineering materials with mechanical, thermal, and electrical properties within the Engineering Metrology, SI/Imperial Unit Conversion & Applied Physics domain using the governing formulation: Searchable database of 200+ engineering materials with mechanical, thermal, and electrical properties.. All intermediate quantities are computed in double-precision floating-point arithmetic to prevent cumulative rounding drift before final design verification.
Which international engineering standards apply to Engineering Material Properties Database calculations?
Calculations and boundary assumptions in this utility align with recognized industry references including NIST Special Publication 811 (Guide for the Use of the International System of Units), ISO 80000-1 (Quantities and Units), BIPM SI Brochure (9th Edition). When preparing formal calculation packages or P.E. stamp submittals, always verify local jurisdictional code amendments and project-specific safety factors.
How should I integrate results from the Engineering Material Properties Database into my CAD or BIM workflow?
Maintain full double-precision floating-point accuracy during intermediate engineering calculations and apply rounding only to final drawing callouts per ASME Y14.5 / ISO 80000 rules. Using the baseline benchmark (Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = NIST Special Publication 811 (Guide for the Use of the International System of Units)), the solver yields Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready, which can be directly cross-referenced against your parametric 3D assembly constraints, 2D fabrication drawings, or bill of materials (BOM).