Standard Sheet Metal Gauge Thickness Chart (Steel, Stainless, Galvanized, Al)
Gauge to millimeter and inch cross-reference chart (10 Ga to 24 Ga) for standard carbon steel, galvanized, stainless steel, and aluminum.
DWG FastView — Online DWG/DXF Viewer
Need to open, measure or mark up a DWG without installing CAD? DWG FastView runs in the browser. This is a sponsored placement and has no effect on the results of the tool above.
Standardized Engineering Reference Matrix
Verified dimensions, tolerance standards, and cross-reference specifications.
| Gauge No. | Carbon Steel (mm / in) | Galvanized Steel (mm / in) | Stainless Steel (mm / in) | Aluminum Sheet (mm / in) | Action |
|---|---|---|---|---|---|
| 10 Ga | 3.416 mm (0.1345") | 3.505 mm (0.1382") | 3.571 mm (0.1406") | 2.588 mm (0.1019") | |
| 12 Ga | 2.657 mm (0.1046") | 2.746 mm (0.1084") | 2.779 mm (0.1094") | 2.052 mm (0.0808") | |
| 14 Ga | 1.897 mm (0.0747") | 1.994 mm (0.0785") | 1.984 mm (0.0781") | 1.628 mm (0.0641") | |
| 16 Ga | 1.519 mm (0.0598") | 1.613 mm (0.0635") | 1.588 mm (0.0625") | 1.290 mm (0.0508") | |
| 18 Ga | 1.214 mm (0.0478") | 1.311 mm (0.0516") | 1.270 mm (0.0500") | 1.024 mm (0.0403") | |
| 20 Ga | 0.912 mm (0.0359") | 1.006 mm (0.0396") | 0.953 mm (0.0375") | 0.813 mm (0.0320") | |
| 22 Ga | 0.759 mm (0.0299") | 0.853 mm (0.0336") | 0.792 mm (0.0312") | 0.643 mm (0.0253") | |
| 24 Ga | 0.607 mm (0.0239") | 0.701 mm (0.0276") | 0.635 mm (0.0250") | 0.511 mm (0.0201") |
Next Steps in Your Mechanical Workflow
Handpicked calculators, parsers, and shortcuts for sheet metal, modeling & fabrication
Sheet Metal Bend Deduction & K-Factor Quick Reference Chart
Bend deduction, bend allowance, and K-factor values for common sheet metal materials and thicknesses.
Pipe Size Chart (NPS/DN/Schedule) Reference
Complete pipe size chart: NPS to DN conversion, outside diameter, wall thickness for Schedule 10-160 and XS/XXS, with weight and bore data.
PVC Pipe Schedule 40 & Schedule 80 Dimensions & Pressure Ratings Table
ASTM D1785 rigid PVC pipe dimensions (1/2" to 8"): outside diameter, Sch 40 and Sch 80 wall thicknesses, and max operating PSI at 73°F.
Sand Casting Yield Calculator
Calculate casting yield, pouring weight, and feed metal from part and riser weights.
Insulation Thickness Calculator
Calculate required insulation thickness for target heat loss or surface temperature.
2026 CAD Workstation Hardware Spec Matrix
Match your CAD/BIM software and assembly size to optimal CPU single-core GHz, RAM & GPU.
Engineering Methodology & Design Standards: Standard Sheet Metal Gauge Thickness Chart (Steel, Stainless, Galvanized, Al)
Discipline: CNC Machining, Sheet Metal Fabrication & Dimensional Metrology
Governing Mathematical Formulation
In professional CNC Machining, Sheet Metal Fabrication & Dimensional Metrology workflows, accurate sizing and performance verification require consistent unit normalization and adherence to closed-form analytical mechanics. This Standard Sheet Metal Gauge Thickness Chart (Steel, Stainless, Galvanized, Al) utility implements the standardized engineering formulation:
Gauge to millimeter and inch cross-reference chart (10 Ga to 24 Ga) for standard carbon steel, galvanized, stainless steel, and aluminum.Gauge to millimeter and inch cross-reference chart (10 Ga to 24 Ga) for standard carbon steel, galvanized, stainless steel, and aluminum. Every input change triggers an instant client-side recalculation across all coupled dependent variables, enabling rapid sensitivity analysis during preliminary and detailed CAD design phases.
Applicable Codes, Standards & CAD Integration
Synchronize sheet metal K-factors, tool radius compensation registers (G41/G42), and GD&T datum reference frames between your 3D CAD master model, CAM post-processor, and CMM inspection plan.
Engineering Verification Note: Analytical models assume homogeneous material behavior, steady-state boundary loading, and consistent dimensional units. Always apply appropriate service factors, corrosion allowances, or load and resistance factor design (LRFD / ASD) safety margins required by your governing code.
Parameter Specifications & Worked Engineering Example
Baseline reference case using default design values for Standard Sheet Metal Gauge Thickness Chart (Steel, Stainless, Galvanized, Al)
Step-by-Step Benchmark Walkthrough
- Define Design Boundary Conditions: Establish the nominal operating parameters for the component or system:
Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = ISO 286-1 / ASME B4.1 (Limits and Fits). Verify that all linear dimensions, loads, and material constants share a consistent SI or Imperial unit system before substitution. - Execute Analytical Formulation: Substitute the normalized input vector into the governing relation (
Gauge to millimeter and inch cross-reference chart (10 Ga to 24 Ga) for standard carbon steel, galvanized, stainless steel, and aluminum.) in accordance with ISO 286-1 / ASME B4.1 (Limits and Fits), ASME Y14.5-2018 / ISO 1101 (GD&T), DIN 6935 (Sheet Metal Cold Bending), ISO 2768 (General Tolerances). - Verify Computed Engineering Outputs: For the baseline design case, the calculator yields
Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready. Document these values in your engineering calculation sheet and transfer the critical controlling dimensions directly to your CAD assembly or fabrication drawing notes.
Frequently Asked Engineering Questions
Technical reference & verification guidelines for Standard Sheet Metal Gauge Thickness Chart (Steel, Stainless, Galvanized, Al)
What governing equation and methodology does the Standard Sheet Metal Gauge Thickness Chart (Steel, Stainless, Galvanized, Al) use?
The Standard Sheet Metal Gauge Thickness Chart (Steel, Stainless, Galvanized, Al) evaluates gauge to millimeter and inch cross-reference chart (10 ga to 24 ga) for standard carbon steel, galvanized, stainless steel, and aluminum within the CNC Machining, Sheet Metal Fabrication & Dimensional Metrology domain using the governing formulation: Gauge to millimeter and inch cross-reference chart (10 Ga to 24 Ga) for standard carbon steel, galvanized, stainless steel, and aluminum.. All intermediate quantities are computed in double-precision floating-point arithmetic to prevent cumulative rounding drift before final design verification.
Which international engineering standards apply to Standard Sheet Metal Gauge Thickness Chart (Steel, Stainless, Galvanized, Al) calculations?
Calculations and boundary assumptions in this utility align with recognized industry references including ISO 286-1 / ASME B4.1 (Limits and Fits), ASME Y14.5-2018 / ISO 1101 (GD&T), DIN 6935 (Sheet Metal Cold Bending), ISO 2768 (General Tolerances). When preparing formal calculation packages or P.E. stamp submittals, always verify local jurisdictional code amendments and project-specific safety factors.
How should I integrate results from the Standard Sheet Metal Gauge Thickness Chart (Steel, Stainless, Galvanized, Al) into my CAD or BIM workflow?
Synchronize sheet metal K-factors, tool radius compensation registers (G41/G42), and GD&T datum reference frames between your 3D CAD master model, CAM post-processor, and CMM inspection plan. Using the baseline benchmark (Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = ISO 286-1 / ASME B4.1 (Limits and Fits)), the solver yields Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready, which can be directly cross-referenced against your parametric 3D assembly constraints, 2D fabrication drawings, or bill of materials (BOM).