ASME B16.5 Pipe Flange Dimensions & Bolt Specifications Reference Table
Complete ASME B16.5 Class 150 pipe flange dimensions: outside diameter, bolt circle, bolt holes, and stud lengths (1/2" to 24").
DWG FastView — Online DWG/DXF Viewer
Need to open, measure or mark up a DWG without installing CAD? DWG FastView runs in the browser. This is a sponsored placement and has no effect on the results of the tool above.
Standardized Engineering Reference Matrix
Verified dimensions, tolerance standards, and cross-reference specifications.
| NPS (Nominal Size) | Flange OD (mm / in) | Bolt Circle BC (mm / in) | Number of Bolts | Bolt Hole Dia (mm) | Bolt Stud Dia x Length | Action |
|---|---|---|---|---|---|---|
| 1/2" (DN 15) | 88.9 mm (3.50") | 60.3 mm (2.38") | 4 | 15.9 mm | 1/2" x 2.25" | |
| 3/4" (DN 20) | 98.4 mm (3.88") | 69.8 mm (2.75") | 4 | 15.9 mm | 1/2" x 2.50" | |
| 1" (DN 25) | 108.0 mm (4.25") | 79.4 mm (3.12") | 4 | 15.9 mm | 1/2" x 2.50" | |
| 1-1/2" (DN 40) | 127.0 mm (5.00") | 98.4 mm (3.88") | 4 | 15.9 mm | 1/2" x 2.75" | |
| 2" (DN 50) | 152.4 mm (6.00") | 120.6 mm (4.75") | 4 | 19.0 mm | 5/8" x 3.25" | |
| 3" (DN 80) | 190.5 mm (7.50") | 152.4 mm (6.00") | 4 | 19.0 mm | 5/8" x 3.50" | |
| 4" (DN 100) | 228.6 mm (9.00") | 190.5 mm (7.50") | 8 | 19.0 mm | 5/8" x 3.50" | |
| 6" (DN 150) | 279.4 mm (11.00") | 241.3 mm (9.50") | 8 | 22.2 mm | 3/4" x 4.00" | |
| 8" (DN 200) | 342.9 mm (13.50") | 298.4 mm (11.75") | 8 | 22.2 mm | 3/4" x 4.25" | |
| 10" (DN 250) | 406.4 mm (16.00") | 362.0 mm (14.25") | 12 | 25.4 mm | 7/8" x 4.75" | |
| 12" (DN 300) | 482.6 mm (19.00") | 431.8 mm (17.00") | 12 | 25.4 mm | 7/8" x 5.00" |
Recommended Engineering & CAD Utilities
Handpicked companion tools to streamline modeling, calculation, and drafting workflows
ANSI / ASME B1.1 Unified Inch Screw Threads (UNC / UNF) Database
Standard dimensions for Unified inch fasteners: major diameter, TPI, pitch diameter, minor diameter, and recommended tap drill sizes.
Gasket Sealing Pressure Calculator
Calculate gasket seating pressure and bolt torque for flanged joints. Free browser-based engineering calculator.
ISO 2768 General Tolerances Reference Table
ISO 2768-1/2 general tolerances for linear dimensions, angular dimensions, and geometrical tolerances across four accuracy classes (fine, medium, coarse, very coarse).
ADA Ramp Slope & Landing Calculator
Calculate ADA-compliant ramp slope, run length, landing dimensions, and handrail requirements.
Excavation Volume & Cost Calculator
Calculate excavation volume, truck loads, and cost from trench dimensions.
AutoCAD vs GstarCAD Shortcuts
Side-by-side comparison of command alias compatibility and migration differences.
Engineering Methodology & Design Standards: ASME B16.5 Pipe Flange Dimensions & Bolt Specifications Reference Table
Discipline: Fastener Engineering & Bolted Joint Mechanics
Governing Mathematical Formulation
In professional Fastener Engineering & Bolted Joint Mechanics workflows, accurate sizing and performance verification require consistent unit normalization and adherence to closed-form analytical mechanics. This ASME B16.5 Pipe Flange Dimensions & Bolt Specifications Reference Table utility implements the standardized engineering formulation:
Complete ASME B16.5 Class 150 pipe flange dimensions: outside diameter, bolt circle, bolt holes, and stud lengths (1/2" to 24").Complete ASME B16.5 Class 150 pipe flange dimensions: outside diameter, bolt circle, bolt holes, and stud lengths (1/2" to 24"). Every input change triggers an instant client-side recalculation across all coupled dependent variables, enabling rapid sensitivity analysis during preliminary and detailed CAD design phases.
Applicable Codes, Standards & CAD Integration
Ensure clearance hole diameters conform to ISO 273 / ASME B18.2.8 medium fit series and verify minimum thread engagement length (typically 1.0×d in steel, 2.0×d in aluminum) in your assembly BOM.
Engineering Verification Note: Analytical models assume homogeneous material behavior, steady-state boundary loading, and consistent dimensional units. Always apply appropriate service factors, corrosion allowances, or load and resistance factor design (LRFD / ASD) safety margins required by your governing code.
Parameter Specifications & Worked Engineering Example
Baseline reference case using default design values for ASME B16.5 Pipe Flange Dimensions & Bolt Specifications Reference Table
Step-by-Step Benchmark Walkthrough
- Define Design Boundary Conditions: Establish the nominal operating parameters for the component or system:
Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = VDI 2230 (Systematic Calculation of High Duty Bolted Joints). Verify that all linear dimensions, loads, and material constants share a consistent SI or Imperial unit system before substitution. - Execute Analytical Formulation: Substitute the normalized input vector into the governing relation (
Complete ASME B16.5 Class 150 pipe flange dimensions: outside diameter, bolt circle, bolt holes, and stud lengths (1/2" to 24").) in accordance with VDI 2230 (Systematic Calculation of High Duty Bolted Joints), ISO 898-1 (Mechanical Properties of Carbon & Alloy Steel Fasteners), ASME B1.1 / ISO 68-1. - Verify Computed Engineering Outputs: For the baseline design case, the calculator yields
Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready. Document these values in your engineering calculation sheet and transfer the critical controlling dimensions directly to your CAD assembly or fabrication drawing notes.
Frequently Asked Engineering Questions
Technical reference & verification guidelines for ASME B16.5 Pipe Flange Dimensions & Bolt Specifications Reference Table
What governing equation and methodology does the ASME B16.5 Pipe Flange Dimensions & Bolt Specifications Reference Table use?
The ASME B16.5 Pipe Flange Dimensions & Bolt Specifications Reference Table evaluates complete asme b16.5 class 150 pipe flange dimensions: outside diameter, bolt circle, bolt holes, and stud lengths (1/2" to 24") within the Fastener Engineering & Bolted Joint Mechanics domain using the governing formulation: Complete ASME B16.5 Class 150 pipe flange dimensions: outside diameter, bolt circle, bolt holes, and stud lengths (1/2" to 24").. All intermediate quantities are computed in double-precision floating-point arithmetic to prevent cumulative rounding drift before final design verification.
Which international engineering standards apply to ASME B16.5 Pipe Flange Dimensions & Bolt Specifications Reference Table calculations?
Calculations and boundary assumptions in this utility align with recognized industry references including VDI 2230 (Systematic Calculation of High Duty Bolted Joints), ISO 898-1 (Mechanical Properties of Carbon & Alloy Steel Fasteners), ASME B1.1 / ISO 68-1. When preparing formal calculation packages or P.E. stamp submittals, always verify local jurisdictional code amendments and project-specific safety factors.
How should I integrate results from the ASME B16.5 Pipe Flange Dimensions & Bolt Specifications Reference Table into my CAD or BIM workflow?
Ensure clearance hole diameters conform to ISO 273 / ASME B18.2.8 medium fit series and verify minimum thread engagement length (typically 1.0×d in steel, 2.0×d in aluminum) in your assembly BOM. Using the baseline benchmark (Input Geometry / Parameter Stream = Client-Side CAD / Numeric Input, Verification Tolerance Standard = VDI 2230 (Systematic Calculation of High Duty Bolted Joints)), the solver yields Diagnostic & Compliance Verdict = 100% Standards-Verified Output; Downstream CAD/CAM Readiness = Production-Ready, which can be directly cross-referenced against your parametric 3D assembly constraints, 2D fabrication drawings, or bill of materials (BOM).